Raman Spectroscopy Filters
Laser-line, dichroic and notch filters matched to one laser
PB01 · IMAGE PENDINGRaman laser-line and notch filtersLaser-Line, Dichroic and Notch Filters for Raman Systems
Raman light is far weaker than the laser that creates it. Filters decide whether it reaches the detector cleanly or is buried under laser light.
A Raman system usually needs a laser-line filter on the way in and a notch or edge filter on the way out.
We make ultra-narrow laser-line filters at 514 and 532 nm, down to 0.3 nm wide, with OD4 to OD5 blocking.
Our Raman notch filters at 405, 785 and 808 nm block the laser at OD4 and transmit 88% to 93% on either side.
Need a full set for one laser? Send us the wavelength and we will match all the filters.
For broadband Raman collection, hard-coated filters from 345 to 1,650 nm, 80 to 300 nm wide, are designed around the standard Raman laser lines and suit high temperatures.
Choosing the Laser Wavelength
Shorter wavelengths, such as 405, 514 or 532 nm, give stronger Raman signals, but many samples fluoresce and swamp the spectrum.
785 nm is a common compromise: much less fluorescence, a strong enough signal, and Raman lines that a silicon detector can still see.
1,064 nm reduces fluorescence further but needs an InGaAs detector. Whichever you choose, every filter in the set must be matched to that one laser.
A Complete Raman Filter Set
Laser-line filter. Diode lasers emit a weak broad background beside the line. An ultra-narrow bandpass filter removes it, so it is not mistaken for Raman signal. View details
D01 · IMAGE PENDINGBackscatter Raman light path with three filtersDichroic beamsplitter. In backscatter probes, the laser and the Raman light share one path. A 45° dichroic or notch dichroic reflects the laser to the sample and passes the returning Raman light.
All three filters must share the same laser wavelength and the same angle as your optical design.
Transmission-only setups, with the laser and the collection at an angle, can skip the dichroic.
Rayleigh rejection filter. Before the spectrometer, a notch or longpass edge filter blocks laser light scattered back from the sample. It must block at OD4 or more at the laser line. View details
D02 · IMAGE PENDINGNotch versus longpass edge on a Raman spectrumNotch and longpass edge filters suppress the excitation line while passing different portions of the Raman spectrum.
Notch or edge? A notch filter blocks a narrow band around the laser and transmits on both sides, so you can record Stokes and anti-Stokes lines with one filter. It is also the choice when two lasers share a system.
A longpass edge filter blocks everything below a cut-on just above the laser and records Stokes lines only. Edge filters are simpler and are often chosen when anti-Stokes lines are not needed.
Our standard Raman filters are notches. Edge filters for 532, 785 or 1,064 nm are made to order. Tell us how close to the laser you need to measure, and we will set the cut-on and blocking to suit.
Raman Filters by Laser Wavelength
| Laser (nm) | Laser-line filter | Rayleigh rejection filter |
|---|---|---|
| 405 | On request | Notch 405nm-20nm |
| 514 | Ultra-NBP514-2 | On request |
| 532 | Ultra-NBP532-1 (FWHM < 1, < 0.6 or < 0.3 nm) | Notch design, on request |
| 785 | Ultra-NBP785-1.2 | Notch 785nm-35nm |
| 808 | On request | Notch 808nm-35nm |
| 1,064 | Ultra-NBP1064-0.5 | On request |
Full specifications are on each filter’s page. For a missing filter, we can design one to match the rest of your set.
What to Send Us
- Laser wavelength and linewidth
- Closest Raman shift you need, in cm⁻¹
- Stokes only, or anti-Stokes too
- Detector: silicon or InGaAs
- Angle and beam size at each filter
- Filter size and quantity
Building a Raman spectrometer or probe? Send us your laser, the closest shift you need and your detector, and we will match the laser-line, dichroic and blocking filters as one set. Contact us
