Neutral Density Filters
Pick a standard filter below, or send us your wavelength for a custom design.
Neutral Density Filters from 90% to 0.01% Transmission
When a laser, lamp or camera scene is too bright for your detector, a neutral density (ND) filter turns it down by a set factor across a wide band, without changing the color balance.
We make ND filters from 90% down to 0.01% transmission, roughly OD 0.05 to OD4.
Absorptive glass filters cover 400 to 1,100 nm, broadband attenuators reach from 300 to 1,800 nm, and a reflective OD3 filter covers 350 to 650 nm.
Each filter comes with a stated transmission tolerance, shown here in OD as well.
ND filter sets of 7, 14 or 17 filters come calibrated, with individual spectral data and a storage case. Metallic ND filters cover 250 to 2,000 nm, and infrared ND filters on germanium cover 2 to 14 µm at OD 0.3 to 3.0.
Need another density, range or size? Ask us for a custom ND filter. Specify a custom filter
What “Neutral” Means on a Spec Sheet
Neutral means the transmission stays close to its nominal value across a stated range. A 10% filter specified over 350 to 1,100 nm should pass about one tenth of the light at every wavelength in that range.
So check two numbers: the range and the tolerance. Our 5 to 40% absorptive filters hold ±3 percentage points over 400 to 1,100 nm, and the 50 to 90% filters ±5 points.
Outside the stated range, the filter is no longer neutral. Our deepest absorptive filters, 0.01 to 1%, are specified only from 400 to 700 nm.
Reflective, Absorptive and Broadband
Reflective ND
A reflective coating sends the unwanted light back instead of absorbing it, so the filter stays cool under strong light. Ours is OD3 (0.1% average) from 350 to 650 nm. Mind where the reflected beam goes.
Absorptive Glass ND
K9 glass absorbs a fixed share of the light, with very little reflected back into your system, which suits imaging. Thirteen steps from 90% to 0.01%; the deepest are specified from 400 to 700 nm.
Broadband Attenuators
For wide spectral ranges: 10% from 350 to 1,100 nm, and 50% from 300 to 1,800 nm, covering UV, visible and short-wave infrared with one filter.
| Nominal T | Nominal OD | Specified range | OD range |
|---|---|---|---|
| 90% | 0.05 | 85–95% | 0.02–0.07 |
| 50% | 0.30 | 45–55% | 0.26–0.35 |
| 10% | 1.0 | 7–13% | 0.89–1.15 |
| 5% | 1.3 | 2–8% | 1.10–1.70 |
| 1% | 2.0 | 0.5–2% | 1.70–2.30 |
| 0.1% | 3.0 | 0.05–0.5% | 2.30–3.30 |
| 0.01% | 4.0 | 0.005–0.05% | 3.30–4.30 |
Transmission and OD, Side by Side
OD is the base-10 logarithm of attenuation: OD1 passes 10%, OD2 1%, OD3 0.1%, OD4 0.01%. Stack two ND filters and their ODs add, so OD1 plus OD2 gives about OD3, ignoring reflections between them.
Tolerances look different in OD. Our 10% filter, ±3 points, spans OD 0.89 to 1.15. The 0.01% filter, specified as 0.005 to 0.05%, spans OD 3.3 to 4.3, a full decade.
If you need a precise attenuation, measure the filter you receive, or ask us for a tighter range. Each filter can be supplied with its measured transmission.
Standard ND Filters
| Model | Transmission | Range (nm) | Type | AOI |
|---|---|---|---|---|
| Reflective ND OD3@350-650 | 0.1% average (OD3) | 350–650 | Reflective | 0 ± 2° |
| ND 10%@350-1100 | 10% average | 350–1,100 | — | 0 ± 2° |
| ND 50%@300-1800 | 50% average | 300–1,800 | — | 0 ± 2° |
Absorptive K9 ND Filters
| Nominal T | Specified range | Range (nm) |
|---|---|---|
| 0.01% | 0.005–0.05% | 400–700 |
| 0.1% | 0.05–0.5% | 400–700 |
| 1% | 0.5–2% | 400–700 |
| 5% | 5% ± 3% | 400–1,100 |
| 10% | 10% ± 3% | 400–1,100 |
| 20% | 20% ± 3% | 400–1,100 |
| 30% | 30% ± 3% | 400–1,100 |
| 40% | 40% ± 3% | 400–1,100 |
| 50% | 50% ± 5% | 400–1,100 |
| 60% | 60% ± 5% | 400–1,100 |
| 70% | 70% ± 5% | 400–1,100 |
| 80% | 80% ± 5% | 400–1,100 |
| 90% | 90% ± 5% | 400–1,100 |
Filters in the first table are specified with a 3.5° cone half-angle. Absorptive filters are K9 glass; ± values are percentage points. Ask us for the curves.
Absorptive K9 ND Filters
| Nominal T | Specified range | Range (nm) |
|---|---|---|
| 0.01% | 0.005–0.05% | 400–700 |
| 0.1% | 0.05–0.5% | 400–700 |
| 1% | 0.5–2% | 400–700 |
| 5% | 5% ± 3% | 400–1,100 |
| 10% | 10% ± 3% | 400–1,100 |
| 20% | 20% ± 3% | 400–1,100 |
| 30% | 30% ± 3% | 400–1,100 |
| 40% | 40% ± 3% | 400–1,100 |
| 50% | 50% ± 5% | 400–1,100 |
| 60% | 60% ± 5% | 400–1,100 |
| 70% | 70% ± 5% | 400–1,100 |
| 80% | 80% ± 5% | 400–1,100 |
| 90% | 90% ± 5% | 400–1,100 |
Filters in the first table are specified with a 3.5° cone half-angle. Absorptive filters are K9 glass; ± values are percentage points. Ask us for the curves.
Need a different density? Send us the transmission or OD you need and its tolerance, the wavelength range, your light source and power, and the size, and we will reply with a quote and a recommended filter. Contact us



