BPF1200-15,OD3

1,200 nm narrowband filter, 15 nm wide, with OD3 blocking from 200 to 1,182 nm and from 1,225 to 1,800 nm.

Need a different size or spec? We make custom versions.

BANDOPTIC spectrum engine

Interactive Spectrum

Plot and compare optical filter spectra. Catalog curves digitized from the supplied PDFs are approximate references; request measured data for specifications.

Choose a filter from the catalog or upload a numerical CSV.

Request measured data

Catalog curves are approximate digital tracings of PDF graph images, not instrument CSV or guaranteed production-lot results. Some curves show only the plotted peak or cut-on edge; open the source graph for its full context. For approximate traces, OD values at or below 2% transmission are hidden because raster plots cannot verify blocking performance. Uploaded CSV files stay in your browser. Andover numerical curves will be added only when source data is available.

Technical Specifications

SpecificationValue
Center wavelength (CWL)1,200 ± 2 nm
Bandwidth (FWHM)15 ± 2.0 nm
Transmission> 93% at 1,200 nm
Blocking, short sideOD > 3 (average), 200–1,182 nm
Blocking, long sideOD > 3 (average), 1,225–1,800 nm
Angle of incidence0 ± 2°
Cone half-angle3.5°
SubstrateOptical glass (K9 / B270)
Thickness1.0 ± 0.1 mm
Dimensional tolerance+0 / −0.1 mm
Surface quality60-40 scratch-dig
Clear aperture≥ 90% of diameter

Sizes

Need custom requirements? We cut to your drawing.

SizeThicknessMount
Ø12.5 mm1.0 mmUnmounted
Ø25 mm1.0 mmUnmounted or ringed
12.5 × 12.5 mm1.0 mmUnmounted

Other sizes and shapes are cut to order.

Choosing This Filter

BPF1200-15,OD3 passes a 15 nm band at 1,200 nm with more than 93% average transmission. It shares its center with BP1200/10,OD3 but is 5 nm wider, so it collects more light when your source is weak or your detector is slow, at the cost of slightly less spectral detail. Its short-side blocking starts at 200 nm and runs to 1,182 nm at OD3, covering the UV and visible as well as the near-infrared; the long side blocks from 1,225 to 1,800 nm. That makes it safe to use with broadband lamps and with silicon or InGaAs detectors. The cards below list our other lines around 1,200 nm.

Customization Options

Need a different wavelength, width or blocking? We design it to order.

We can move the center wavelength anywhere from 200 to 2,500 nm, change the width, block deeper, up to OD6, or further into the infrared, and cut the filter to your size and thickness.

Tell us your light source, your detector and the numbers you need. We will reply with a recommended design and a quote, from a single prototype to production volumes.

See what we can make on our custom filters page. Learn more

FAQs

Can I tilt this filter?

A small tilt, up to about 2°, stays within spec. Beyond that, the passband moves to shorter wavelengths, and the further you tilt, the further it moves. If your design needs a tilt, tell us the angle and we will design for it.

How should I clean and store it?

Hold the filter by its edges. Blow off dust first, then wipe gently with lens tissue and reagent-grade isopropyl alcohol if needed. Store it dry, in its case, away from direct sunlight.

Can I get the measured curve with my order?

Yes. Ask for it when you order, and we include the measured transmission of your batch, as a chart and as a data file.

Don’t see the filter you need? Tell us about your system and we will suggest one or design it. Learn more